PLUMBING BASICS: BEFORE INSTALLING A BATHTUB

Plumbing Basics: Before Installing a Bathtub

Plumbing Basics: Before Installing a Bathtub

Blog Article

Visit Website

The content down below involving How to Install a Bathtub: Install an Acrylic Tub and Tub Surround is fairly intriguing. Don't miss out on it.


Installing A Bathtub
Mounting a bath tub isn't exactly brain surgery, however it does need solid plumbing, woodworking, and in some cases, tiling skills. Changing an old tub with a brand-new one is additionally a moderately difficult job. If the old tub is readily obtainable, the task can relocate speedily; if you have to open a wall to get rid of the old tub and also position the new bathtub, the job is a lot harder. In either situation, the task is within a house handyman's skills, although you will certainly need a helper to leave the old tub and embeded in the new one. Ensure you have qualified on your own for the task and also fit trying it. Rather than employing a service provider to take over a halfway-completed task, it is far better to consider using one before you start. Chances are you may require a professional plumber to make tube links.
This write-up will help you install a new bathtub in your shower room if you have actually currently acquired a new tub and don't require to alter the arrangement of your previous water supply pipes.
Your tools as well as product checklist need to consist of the following:
  • New Tub

  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Shatterproof glass

  • Level

  • Pliers

  • Adjustable Wrench

  • Putty Blade

  • Screwdriver

  • Cold Chisel

  • Tape Measure

  • Pipe Caps


  • Removing Old Taps


    If you need to change old faucets with brand-new ones as a part of your installment, then the first thing you should do is disconnect the supply of water. After doing so, turn on the faucets to drain pipes any kind of water remaining in the system. The process of eliminating the existing faucets can be rather problematic because of the limited accessibility that is commonly the instance.
    Utilize a basin wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipelines to the faucets. Have a cloth all set for the staying water that will originate from the pipelines. When the supply pipelines have been eliminated, use the exact same tool to loosen the nut that holds the faucets onto the bath/basin. You will need to quit the single taps from transforming during this procedure. As soon as the taps have been gotten rid of, the holes in the bath/basin will need to be cleaned up of any old sealing substance.
    Before going on to fit the new faucets, contrast the pipeline links on the old faucets to the brand-new taps. If the old taps are longer than the new faucets, then a shank adapter is required for the brand-new faucets to fit.

    Fitting New Touches


    If the tails of the brand-new taps are plastic, after that you will require a plastic adapter to avoid damage to the string. One end of the connector fits on the plastic tail of the tap and the other end supplies a connection to the existing supply pipelines.
    If you require to fit a monobloc, after that you will certainly require lowering couplers, which connects the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
    Next, position the faucet in the mounting opening in the bath/basin making sure that the washers are in place in between the tap as well as the sink. Safeguard the tap in place with the maker given backnut. Once the tap is safely in place, the supply pipes can be connected to the tails of the taps. The taps can either be linked by using corrugated copper piping or with typical faucet connectors. The former kind should be connected to the tap ends first, tightening just by hand. The supply pipelines can later be linked to the various other end. Tighten both ends with a spanner after both ends have actually been attached.

    Setting up the Tub


    Using the two wooden boards under its feet, position the bath tub in the needed placement. The wood boards are useful in evenly spreading out the weight of the bath tub over the area of the boards rather than focusing all the weight onto four little factors.
    The next objective is to guarantee that the bath tub is leveled all round. This can be achieved by checking the level and also adjusting the feet on the bathtub till the level reads level.
    To install faucets, fit all-time low of the outermost flexible faucet connector to the appropriate supply pipeline by making a compression sign up with; after that do the exact same for the various other tap.
    Turn on the supply of water as well as inspect all joints and also new pipework for leaks and also tighten them if required. Load the bathtub as well as additionally examine the overflow outlet and the regular electrical outlet for leakages.
    Finally, repair the bath paneling as explained in the maker's user's manual. Tiling and sealing around the bath tub should wait until the tub has actually been utilized a minimum of when as this will certainly settle it right into its final placement.

    Getting ready for the Installation


    First of all, the sustaining framework supplied with the bath ought to be fitted (if needed) according to the manufacturer's directions. Next, fit the taps or mixer to the bathtub. When fitting the faucet block, it is important to see to it that if the faucet comes with a plastic washer, it is fitted between the bathroom and also the faucets. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the faucets device to prevent stress on the bath tub.
    Fit the adaptable faucet connectors to the bottom of the two taps utilizing 2 nuts and olives (often provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and after that pass the electrical outlet through the hole in the bathroom. Make use of the nut supplied by the producer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
    Next, fit completion of the versatile overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. Make certain you utilize every one of the provided washers.
    Attach the catch to the bottom of the waste outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Attach the bottom of the overflow tube in a similar manner.The bath need to now prepare to be suited its last position.

    Tiling Around the Tub


    In the location where the bath fulfills the tile, it is necessary to seal the joins with a silicone rubber caulking. This is necessary as the installation can move sufficient to split a rigid seal, creating the water to penetrate the wall between the bathroom and also the tiling, bring about issues with dampness and also feasible leakages to the ceiling listed below.
    You can choose from a variety of coloured sealers to blend in your fixtures and fittings. They are sold in tubes as well as cartridges, and also are capable of securing gaps approximately a size of 3mm (1/8 inch). If you have a bigger space to fill, you can fill it with twists of drenched newspaper or soft rope. Remember to constantly load the bathtub with water before sealing, to permit the motion experienced when the tub remains in usage. The sealant can split fairly very early if you do not think about this motion prior to securing.
    Conversely, ceramic coving or quadrant tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are also quickly available on the marketplace. It is a good idea to fit the floor tiles using waterproof or water resistant sticky and also cement.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    How to Install a Bathtub: Install an Acrylic Tub and Tub Surround

    Do you appreciate more info about How to Install a Bathtub Yourself? Try to leave a remark down below. We'd be interested to know your suggestions about this content. We are looking forward that you visit us again in the future. Sharing is nice. You just don't know, you might be doing someone a favor. Thanks a lot for your time. Visit again soon.


    Trusted service? Dial!

    Report this page